Freescale Introduces First CAN-Based Intelligent Sensor for Automotive Battery Monitoring
Automotive-qualified sensor offers robust, cost-effective solution for precisely monitoring battery voltage, current and temperature
TOKYO--(BUSINESS WIRE)-- Freescale Semiconductor (FSL) today introduced the MM9Z1J638 Xtrinsic battery sensor, the industrys first CAN-based battery sensor that accurately measures the voltage, current and temperature of lead-acid and lithium-ion batteries, as well as calculating the battery state all while operating in harsh automotive conditions. Accurate knowledge of these battery parameters has become critical due to the increase in hybrid vehicles and overall electronic content, as well as the introduction of start-stop systems in automobiles.
The MM9Z1J638 Xtrinsic battery sensor offers a robust and cost-effective solution for designers, enabling precision measurement of key battery parameters in automotive and industrial applications. The device integrates an S12Z microcontroller (MCU) and a SMARTMOS analog control integrated circuit in a single-package solution, providing low power consumption in automotive and industrial environments. The MM9Z1J638 Xtrinsic battery sensor is fully AEC-Q100 automotive qualified for operation from -40°C to +125°C and comes in a small form factor, 7 x 7mm QFN package.
Devices such as the intelligent battery sensor are becoming necessary as electronic content and start-stop systems in automobiles continue to increase in quantity and importance, said Gavin Woods, vice president and general manager of Freescales Analog & Mixed-Signal Products Division. We are providing the industrys first CAN-based, automotive-qualified and cost-effective solution that enables precise monitoring of critical battery parameters.
In todays vehicles, the rising number of electrical loads presents a challenge to the battery. It must be able to provide enough energy to crank the engine, as well as act as a passive power source to support new functions such as start-stop and intelligent alternator control. Precise knowledge of the batterys state of health (SOH), state of charge (SOC) and state of function (SOF) can provide early detection of impending failure, the leading cause of vehicle breakdowns due to the electrical system. In addition, the power consumption of the battery sensor itself must be as low as possible to ensure energy efficiency.
Freescales fully integrated battery monitoring device includes a two-channel, 16-bit analog to digital converter (ADC) for simultaneous measurement of battery voltage and current and an independent 16-bit ADC for temperature measurement. The battery sensor provides accurate monitoring with high resolution even in worst-case conditions to allow a proper prediction of the batterys SOH, SOC and SOF. The battery sensor can communicate these parameters at intervals or on request from the in-vehicle network via either the LIN or CAN protocols (CAN requires an external PHY).
The MM9Z1J638 supports precise current measurement via an external shunt resistor at the negative terminal of the battery and precise battery voltage measurement via a series resistor at the positive terminal. The integrated temperature sensor combined with battery mounting allows accurate battery temperature measurement. Eternal temperature sensor inputs allow accurate cell temperature measurement.
MM9Z1J638 Xtrinsic battery sensor characteristics:
Battery voltage measurement
- Dedicated 16-bit second-order sigma-delta (£) ADC with four dedicated voltage inputs covering different measurement ranges (10V, 16V, 28V, 52V)
- Simultaneous sampling with current channel
- Programmable signal filtering shared with current measurement
- Four battery voltage measurement w/ internal divider
- Five voltage sensor inputs routable to both voltage and temperature channels
Differential battery current measurement
- Dedicated 16-bit second order £ ADC with a programmable gain amplifier with four programmable gain factors
- Gain control block for automatic gain adjustment
- Measurement range up to +/-2000A with an accuracy of 5 mA and a resolution of 1 mA
- Internal on-chip temperature sensor
- Dedicated 16-bit ADC with anti-aliasing filter
- Accuracy: +/-2°C (-20 to 60°C) and +/-3°C (-40 to 125°C)
- Five single ended sensor can be routed to Tsense ADC (PTBx) for ratio metric measurement (IC provides power supply and switchable ground allowing current saving when not used)
- Ground switch to reduce power consumption when temperature measurement is off
Normal and low-power modes
- Current integration via 32-bit accumulator during low power mode
- Programmable current threshold detection during low power mode
- Programmable wake-up timer, triggered wake-up from LIN
Advanced system level management
- Internal oscillator with one percent accuracy
- Built-in automatic ADC temperature compensation for optimum measurement accuracy over specified temperature range.
- Communication via LIN 2.1, LIN 2.0 interface with fast mode for flash programming over LIN
- An msCAN protocol controller with TxD and RxD terminals and bus wake-up detection
- Enhanced 5V regulator capability to supply MCU, CAN PHY and other external components.
- High-performance S12Z MCU with 32-bit ALU, 50 Mhz, 128 kByte flash, 8 kByte RAM, 4 kByte EEPROM all with ECC
- Fast, die-to-die bus interface with transparent integration of analog IC registers into the MCU register map, automatic synchronization and error detection
- Operating conditions
- Ambient operating temperature: -40°C < Ta < 125°C
- Junction operating temperature: -40°C < Tj < 150°C
Availability and pricing
The automotive-grade MM9Z1I638 and MM9Z1J638 devices are scheduled to be broadly available by the second half of 2013 from Freescale and authorized distributors worldwide for a suggested resale price of $4.25 and $4.41 (USD) in 10,000-unit quantities, respectively.
About the Freescale Technology Forum
Created to drive innovation and collaboration, the Freescale Technology Forum (FTF) has become one of the developer events of the year for the embedded systems industry. The Forum has drawn more than 48,000 attendees at FTF events worldwide since its inception in 2005. The FTF Japan 2012 event will take place Oct. 22-23 in Tokyo. For more information, visit www.freescale.com/FTFJapan.
About Freescale Semiconductor
Freescale Semiconductor is a global leader in embedded processing solutions, providing industry leading products that are advancing the automotive, consumer, industrial and networking markets. From microprocessors and microcontrollers to sensors, analog integrated circuits and connectivity our technologies are the foundation for the innovations that make our world greener, safer, healthier and more connected. Some of our key applications and end-markets include automotive safety, hybrid and all-electric vehicles, next generation wireless infrastructure, smart energy management, portable medical devices, consumer appliances and smart mobile devices. The company is based in Austin, Texas, and has design, research and development, manufacturing and sales operations around the world. www.freescale.com
Freescale, the Freescale logo and Xtrinsic are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. © 2012 Freescale Semiconductor, Inc.
Andy North, 512-996-4418
Gloria Shiu, (85-22) 666-8237
Europe, Middle East and Africa
Laurent Massicot, (33-16) 935-7712
Anjali Srivastava, (91-120) 395-0000
Hiroyasu Oya, (81-3) 5437-9444
Source: Freescale SemiconductorCopyright Business Wire 2012